Room planning

Golf simulator flooring: record the layer order

Record the floor as separate layers: the support surface, any base, the stance turf, and the hitting panel. Two Fiberbuilt instructions use different orders. Measure the finished height of the stack you install and hand that number to the ceiling and component checks. Do not add published thicknesses together.

Line drawing of a simulator bay with a dashed arc running from the ball position toward the screen. GolfCompat card for flooring layers.

Record each layer before you add the next

A simulator floor is a stack, and each piece in the stack has its own sheet. Write down the support surface first. Then note any separate base, the stance area, and the hitting panel or replaceable strip. Leave a blank for the finished height and fill it only after those pieces are in place.

Hand that measured height to the room-dimensions guide when a mounting instruction starts at the top of the hitting area, and to the ceiling-height guide when you compare a room measurement with a sensor bracket. The component fit checks keep named mat, net and screen dimensions. The net guide keeps containment measurements. This page keeps the layer order.

Keep the two Fiberbuilt orders separate

Fiberbuilt's Grass installation page says to lay the Fiberbuilt Grass hitting panels into their base slots first, so they sit in the base, and then to place the Performance Turf stance and spacer sections. That order belongs to the Grass mats on that page.

The same page splits outdoor ground prep from indoor placement. Outdoors, it names firm, flat surfaces such as concrete pads, asphalt pads, wood decks, patio stones, or firm, packed crushed stone, and it says not to install on grass. In the outdoor concrete sentence, Fiberbuilt says: if you are installing on concrete it is best to ensure that there is a 2% slope to allow for adequate drainage under the mat. Indoors, the same page says Fiberbuilt golf mats and putting greens can go on indoor concrete or carpeted floors. The 2% slope sentence stays in that outdoor concrete section.

Source: FiberbuiltRead November 10, 2026
Installation Recommendations

For Fiberbuilt Grass mats · Publication date not stated for this section

laying the Fiberbuilt Grass hitting panels into their base slots first

Grass mats: hitting panels go into the base slots first, then Performance Turf stance and spacer sections. The 2% slope sentence is in the outdoor concrete section of the same page.

The Player Preferred Series center-hitting sheet, SKU PPS-10X4-760-CH, is a different document for a 10 ft by 4 ft center-hitting mat. It says the surface should be firm, packed and level, and it says not to place the mat on grass. It tells you to place the rubber base pieces (A, B) and the Pure Impact Turf panel (H) on the ground together. The tee holder (F) goes into the underside of the chosen tee location on that panel. Connectors then join the base pieces and the Pure Impact panel. After that, the sheet says to lay the stance turf sections (G) on the base areas that fit their sizes. The parts list names two 4 ft by 4 ft stance turf sections and one 2 ft by 4 ft Pure Impact panel. Keep this order with this sheet.

Source: FiberbuiltRead November 10, 2026
PLAYER PREFERRED SERIES STUDIO MAT CENTER-HITTING - 10'X4'

The surface should be firm, packed and level. · Publication date not stated for this section

Place the rubber base pieces (A, B) and Pure Impact Turf panel (H) on the ground together as shown.

PPS-10X4-760-CH only. Firm, packed and level surface. Do not place on grass. Tee holder from the underside, then connectors, then stance turf G on the base. Separate from the Grass installation page.

Read the DriCore guide as its own subfloor

DriCore's detailed installation guide is about DRICORE Subfloor panels. The guide says it does not recommend a vapour barrier beneath those Subfloor panels, because that could trap moisture. It also says the concrete should be relatively dry and free of large cracks, that the panels are not a replacement for foundation maintenance, and that dips greater than 1/4" should be leveled for a DriCore installation. Those sentences stay with DriCore panels. A golf mat, a stance turf, and a hitting panel still follow their own sheets.

The guide states the panel sizes as DRICORE Subfloor, 3/4" x 23.25" x 23.25", and DRICORE Subfloor R+, 1" x 23.25" x 23.25". Those are the panel dimensions in that guide. Leave them off any total you make for a golf mat. Measure the finished stack you install instead of adding published thicknesses together.

Source: DriCoreRead November 10, 2026
DRICORE DETAILED INSTALLATION GUIDE

Please Note · Publication date not stated for this section

We do not recommend the installation of a vapour barrier beneath our Subfloor panels as doing so could lead to trapped moisture.

DriCore Subfloor panels only. The vapour sentence, the dry-and-free-of-large-cracks sentence, the foundation-maintenance sentence, the 1/4 inch dip sentence, and the two panel sizes do not transfer to a golf mat.

Hand the measured height to the other checks

When the layers you are using are in place, measure from the floor to the top of the hitting surface. Write that finished height next to the layer list. Use it where another instruction starts from the top of the hitting area. A thick stack can change a mounting measurement. The monitor, net, and screen instructions stay the ones published for those products.

Return to the room-fit hub with the layer list and the measured height. Leave an unknown layer blank until you have the sheet for that exact product.

Common questions

Can I add layer thicknesses to get the finished height?

No. A published thickness belongs to the named piece. Measure the top of the hitting surface after the layers you install are in place.

Do the two Fiberbuilt sheets share one install order?

No. The Grass installation page and the Player Preferred Series center-hitting sheet each describe their own order. Keep them separate.

Does the DriCore vapour note apply to a golf mat?

No. That sentence is about DriCore Subfloor panels. It does not set a rule for a golf mat, a stance turf, or a hitting panel.

golf simulator room dimensions

GolfCompat provides planning information. Confirm the instructions for your exact equipment and have your room, swing clearance, and installation assessed before use. A listed equipment requirement does not certify personal safety.